GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. 348 SECTION ANCHORING/MOORING Item# List 686-99010F 68.49 EA Can be used with all styles of Male Corner Hinge. FEMALE CORNER HINGE FOR FLOATING DOCKS Item# List 686-99011F 31.39 EA Can be used with all styles of Male Connector Hinges. FEMALE T CONNECTOR FOR FLOATING DOCKS Item# List 686-DE99012F 24.39 EA Can be used with all styles of Female Connector Hinges. Male T connector (DE99012F) has one welded 1/ 2" tab and to be used with the female T connector (DE99011F) to attach finers and ramps MALE T CONNECTOR FOR FLOATING DOCKS Item# List 686-99013F 51.79 EA Holds chain up to 1/ 2" to secure the dock in place. CHAIN RETAINER FOR FLOATING DOCKS Item# Size List 686-DE90024F 24" Dia. x 8" W 119.44 EA For use at roll-in docks or boat lifts, this tough, rigid wheel offers stress, crack and impact resistance. At 24" (61,0cm) in diameter and an 800lb (362,9kg) capacity per wheel, it rolls easily over virtually any terrain and will not rust on the axle. Wheel accepts a 17/ 8" (4,8cm) O.D. axle. HEAVY DUTY 24" DOCK ROLLING WHEEL Item# Description List 241-26521 Standard Grade 49.59 EA 241-26400 Commercial Grade 72.99 EA A. Two 1/ 2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H. A. OUTSIDE CORNER (FEMALE) 26522 B. Use with a female outside corner to connect docks end to end. Joint requires 3/ 4" bolt set (N) or connector pin (O). Each leg is 10"L x 5" H. B. OUTSIDE CORNER (MALE) Item# Description Size List 241-26522 Standard Grade 1/ 2" Welded Tab 37.99 EA 241-25491 Commercial Grade 1/ 2" Welded Tab 56.89 EA 26523 C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. C. OUTSIDE CORNER END Item# Description Size List 241-26523 Standard Grade Each leg is 10"L x 5"H 30.69 EA 241-26402 Commercial Grade Each leg is 10"L x 5"H 40.89 EA Item# Description Size List 241-26524 Standard Grade 81/ 4"L x 5"H w/ 2" holes 36.49 EA 241-26403 Commercial Grade 81/ 4"L x 5"H w/ 21/ 4" holes 43.79 EA D. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. D. INSIDE CORNER F. Should be used for all cross supports. F. ANGLE Item# Description Size List 241-26527 Standard Grade Each leg 21/ 2"L x 5"H 8.79 EA 241-26406 Commercial Grade Each leg 21/ 2"L x 5"H 11.69 EA G. Bolts to side of dock to attach fingers and ramps. G. FEMALE T CONNECTOR Item# Description Size List 241-26528 Standard Grade w/ 1/ 2" tabs 5" x 5" 36.49 EA 241-26407 Commercial Grade w/ 1/ 2" tabs 5" x 5" 37.99 EA H. Use with Female T connector to attach fingers and ramps. Bolt set "N" required for joint. H. MALE T CONNECTOR Item# Description Size List 241-26532 Standard Grade w/ 1/ 2" tab 5" x 5" 24.89 EA 241-26408 Commercial Grade w/ 1/ 2" tab 5" x 5" 26.29 EA I. Should be used with every Angle. Two required for each Angle. 11/ 2"L x 5"H. I. WASHER PLATE Item# Description List 241-26409 Commercial Grade 4.39 EA J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/ 4", 3/ 8" and 1/ 2" chain. 5"L x 5"H. J. CHAIN RETAINER Item# Description List 241-26529 Standard Grade 23.39 EA 241-26410 Commercial Grade 43.79 EA K. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set "M" required for attaching. K. PIPE HOLDER/OUTSIDE 3" Item# Description List 241-26411 Commercial Grade 66.39 EA
RkJQdWJsaXNoZXIy MTI2MTky