GENERAL BOATING WATERSPORTS & BOATS SEATING COVERS/TOPS MAINTENANCE ELECTRICAL HARDWARE PLUMBING PROPS & ANODES FUEL ELECTRONICS & NAVIGATION SAFETY TROLLING & FISHING ANCHORING/ MOORING TRAILERING PAINT VENTILATION FASTENERS STEERING ENGINE ITEMS ARE STOCKED IN OUR WAREHOUSES BASED ON REGIONAL DEMAND. IF AN ITEM IS NOT IN STOCK AT A LOCAL WAREHOUSE, ADDITIONAL CHARGES MAY APPLY. 988 SECTION STEERING Item# Description Length List 354-5217001 Card 8" 15.29 EA 354-521700 Bulk 8" 11.39 EA Durable molded rubber Steering Cable Boot protects the output end of all standard steering cables keeping dirt, debris, and moisture out and extending the service life of the cable. Includes two cable ties. STEERING CABLE BOOT Item# Size Qty Case List 50-29301 3" 12 13.79 EA 50-29300 3" Bulk 10.11 EA 50-29251 4" 12 18.99 EA 50-29250 4" Bulk 24 15.64 EA Seals off water intake and protects cables, wiring and gas lines. Made of durable vinyl plastisol. MOTORWELL BOOT 29301 29251 Item# Size Case List 50-28251 7/ 8" 12 54.65 EA 50-28261 1" 12 54.07 EA The Steering Guard should be installed on all cable and side-mounted hydraulic steering systems to lubricate, clean and seal the system. Will more than double the life of a new cable system. Made of stainless steel. Installs in 10 minutes. Eliminates greasy steering rods forever. 28251: Fits Honda, Mercury, Mariner, Johnson, Evinrude, Nissan, Suzuki, Tohatsu, Yamaha and Force with 7/ 8" thread. 28261: Fits Honda, Mercury, and Mariner with 1" thread. STEERING GUARD Item# Qty Case List 50-90391 2 12 33.06 PK • Cleans tilt tubes • For use with electric drills • Sold in pairs STEERING TUBE CLEANING BRUSH Item# Case List 50-28301 10 14.39 EA Heavy-duty rubber boot to fit over output end of steering cable at engine for complete protection from elements and preventing lubrication from being washed away. Fits all standard steering cables including Morse, Teleflex, Detmar, etc. Dimensions: 1" ID steering cable end, 3/ 8" ID output end, 11/ 2" overall diameter, 10" extended length, 31/ 2" minimum length. STEERING CABLE PROTECTOR Item# List 166-425 62.48 EA Keeps water and dirt out, lubricants in. Can be used on both mechanical and hydraulic systems. Includes the stainless steel lubricating nut with an oil seal and a grease (zerk) fitting. LUBE II™ STEERING ROD SEALER AND LUBRICATOR RIGGING GROMMET Made of black rubber and plastic. Item# Dia. List 750-610 17/ 8" O.D. / 1" I.D. 9.27 EA 750-615 23/ 4" O.D. / 13/ 4" I.D. 10.63 EA 750-620 33/ 8" O.D. / 21/ 4" I.D. 12.61 EA 750-625 4" O.D, / 3" I.D. 12.14 EA Item# Dia. List 232-BSR1KDP 23/ 4" 47.59 EA Distributes strain from bends in .250 OD to .485 OD hose. Watertight gripper fittingno leaks. Requires 11/ 4" installation hole. For bulk hose only, fittings cannot pass through. BULKHEAD STRAIN RELIEF Item# Model List 232-RFFHP1DP Flange w/fuel hose port 43.19 EA 232-RFHU1DP Flange w/fuel hose union 36.99 EA RFFHP1DP RFHU1DP Split design of union allows installation on pre-rigged boats. Fuel hose port fits type A hose. Installs with TH rigging hose. RIGGING INSTALLATION KIT Item# Dia. Size List 232-FLX50DP 1/ 2"-2" 1/ 2" x 100' 230.59 EA 232-FLX75DP 3/ 4"-3" 3/ 4" x 100' 307.79 EA 232-FLX150DP 11/ 2"-6" 11/ 2" x 50' 289.49 EA A lightweight jacketing for bundling and protecting wires, cables and hoses. Braided from high temperature yarns, T-H Flex™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H Flex™ easy to slip on. T-H FLEX™ SLEEVING Item# Length List 232-ZRS1DP 48" 149.29 EA Protect your cables and hoses with this easy to remove rigging sleeve. Made of rugged Sunbrella® fabric, this sleeve will withstand the elements and resist fading. Easily zips on and off to access cables or hoses when needed. Ends are secured with cable ties sewn into pockets. Black. ZIPPERED RIGGING SLEEVE
RkJQdWJsaXNoZXIy MTI2MTky